Machine de moulage par injection Engel duo 2400/650

This Engel duo 2400/650 electrical injection moulding machine was manufactured in 2019. It features a screw diameter of 60/70/80 mm, a screw stroke of 315 mm, and a maximum injection capacity of 890 cm³. The clamping force reaches up to 6500 kN with a maximum mold weight of 11000 kg. Consider the opportunity to buy this Engel duo 2400/650 electrical injection moulding machine. Contact us for more information about this machine.
Additional equipment
Oil Reservoir Capacity - Injection Unit: 500 l
Maximum Cooling Power (32°C Water Inlet): 29.40 kWcool
Water Consumption (32°C): 4.80 m3/h
Machine Benefits
Qualitative Machine Benefits
The machine has electric water batteries (4 e-flomos with 8 circuits each).
The injection units are fitted with accumulators which enable a high injection pressure of up to 2400 bar with a 60 mm screw.
Technical Machine Benefits
Maximum injection capacity: 890 cm³
Screw torque: 2000 nm // maximum screw speed @ reduced torque: 275 min-1
Reduced torque @ maximum screw speed: 1600 nm
Recovery rate (3-zone screw): 51 g/s // recovery rate (barrier screw): 67. 1 g/s
Injection rate: 353 cm³/s
Nozzle stroke: 950 mm
Ld ratio: 24. 0
Heating zones incl. Nozzle: 8 // heating wattage: 27. 5 kwel
Opening force with pressure pad: 510 kn
Maximum distance between platens: 1750 mm
Extra Information
Dimensions & Weight
Drop Out Chute Width: 1100 mm
Weight of Clamping Unit: 20,000 kg
Maximum Mold Weight (Moving Platen): 7,330 kg
Maximum Mold Weight (Stationary Platen): 7,330 kg
Maximum Mold Weight (Total): 11,000 kg
Cycle Data (Euromap 6)
Stroke: 700 mm
Dry Cycle Time: 2.9 s
Control System: Monocompute CC300
Main Features
21.5” full HD touchscreen
USB interface / Ethernet connection
E-move control element
3 keycards for user login
Graphic symbols for cycle control
Screen languages: German, English
Acoustic error signal / Signal light for error display
Programs & Monitoring
Power Control: optimizes motor performance during dispensing
Mould parallelism measurement
IQ Weight Monitor: monitors shot weight & viscosity
IQ Weight Control: automatic injection parameter adjustment during fluctuations
Quality monitoring interface (injection time, dosing time, pressure, cycle time)
Continuous ejection possible when monitoring is deactivated
Clamping Unit & Plates
Reinforced clamping plates (FAP & BAP +50 mm each)
Reduced min./max. tool height and panel distance (–100 mm due to reinforcement)
FAP: smallest possible platen opening, spherical calotte minimized
BAP: without ejector opening
Additional threads according to EUROMAP VOL1
Centering grooves according to drawing
Plate ejector – Variant A (adapted to clamping pattern)
Safety interface for ejector
Hydraulics & Core Pulls
Hydraulic core pull:1-fold on moving platen2-fold on fixed platen2-fold on moving platen with PQ proportional valve, volume measurement, pressure/speed adjustment
1-fold on moving platen
2-fold on fixed platen
2-fold on moving platen with PQ proportional valve, volume measurement, pressure/speed adjustment
Interface for intermediate core pull position
Mold Heating & Cooling
Mold heating: 16 circuits, max. 40 kW heat output (Euromap 14)
Temperature monitoring interface (moving & fixed platen)
4-fold hydraulic mold nozzle control
Separate cooling water connection (tool & machine)
Temperature control unit interface: Engel protocol, 20 mA current loop
4-way flow regulator (0–10 l/min)
Hose specification: max. 90 °C / 4 bar
Hoses for mold cooling
4 temperature control circuits at rear of machine
Rinsing nozzle with hose clamp
2× ENGEL e-formo temperature control systems (1–15 l/min, 8 circuits, max. 120 °C)
1 distributor for fixed plate, 1 for movable plate
Additional e-formo unit on operating side (optional)
Drive & Hydraulics
ENGEL ecodrive S+V3 (speed-controlled servo drive)
Closed control system for pressure & speed (closed loop)
2× 50 L hydraulic accumulators (for spraying process)
Battery position at the front (as per drawing)
Oil cooler (standard capacity)
Supplied without oil filling (oil contains zinc during commissioning)
Quiet, energy-efficient hydraulics with optimized control, filtration, oil preheating & cooling
Injection Unit
Bi-metallic cylinder (Fe-based), abrasion & corrosion resistant, up to 350 °C
Additional zone heating on barrel
Thrust washer (diaphragm) for screw S8, Ø 60 mm, L/D 24, geometry G1
UNR9 RGB non-return valve (powder metallurgical chrome steel)
Corrosion-resistant flange
Special open nozzle, corrosion-resistant, flange thread V445x3, radius 15 mm, bore 8 mm
Nozzle outlet suitable for hot runner connection
230 V cylinder & nozzle heating
Ceramic cylinder covers
Insulated heating areas (not suitable for PC, PMMA, PVC, etc.)
Electrical System
Supply voltage: 3×400 V + N + PE / 50 Hz
Schuko sockets (230 V), max. 2 pcs
3-phase CEE socket (10/16 A)
Potential-free contacts: 4 inputs / 4 outputs (freely programmable)
Interfaces (Euromap)
13 – Core pull end positions
14 – Heating
63 – Online data access
65 – Tank calculation
Robot & Accessories
ENGEL easix robot (KR 60, special version)
Robot control unit not integrated multiple times
Assembly & test at ENGEL
Operating instructions: printed + CD (German)
Compliance, Design & Extras
EN 201 conformity (machine safety)
Paint finish: RAL 9002 (gray-white) & RAL 5002 (ultramarine blue), special ENGEL design
E-connect.24 basic package (remote maintenance)
Machine feet (standard version)
Labeling in German
All 4 E-Flomo units completely renewed by ENGEL
application type: Injection Moulding
Location: Germany
machine type: Electrical Injection Moulding Machine
control unit brand: ENGEL
Control Brand: ENGEL
Clamping Force: 6500 kN
Screw Diameter: 60 mm